-
HP Drivetech Air Suspension Kit for BMW 5 – F10 (2010-2017
BMW, 5 Series, Drivetech - Air Suspension£2,550.00 inc VAT -
Muecke 3cm Wider Wings Audi RS3 8V ( Inc Facelift )
Muecke-Carbon & Bodywork Parts ( Wider Wings ), A3 / S3 / RS3 H&R Deep Coilover Suspension, A3 / S3 / RS3 HP Drivetech Air SuspensionWhen lowering a car, prime concern is clearance for the steering wheels. These quality Muecke wide wings are available for a variety of vehicles - in some cases in a variety of widths too. Stated widths are per side All of these wings are available in carbon fibre too, for an extra cost. Please contact us if this something you would like to look into, and would like a quote.£449.00 inc VAT- 1 set fiberglass fender Re-Li for Audi A3 8v widened 3 cm per side
- unpainted, surface gelcoat gray
- Material report is included, acceptance according to §21 StVZO (individual acceptance)
- not suitable for saloon
- fits both pre facelift and facelift
£449.00 inc VAT -
H&R Deep Coilover Kit for VW Transporter T5 / T6 / T6.1 T25 T28 T30 Cylindrical Clamp F: 100mm ( 130mm hub mod ) R: 130mm
TransporterTransporter Deep Coilover made by H&R for StillStatic The kit is has front damping adjustment in a stainless steel strut housing and fixed rear damping rear. Comes with 2 years warranty. To fit Cylinder Hub type. Example pictures shows our T32 with approx 10mm threads remaining in the front 9 not hub modded version ) and 20mm threads remaining in the rear without load. H&R Transporter Fits T5 03/03> Multivan, Transporter, California, LKW inc Facelift ( Type 7HK, 7HKXO,7HM,7HMA,7HC,7HCA,7JO,2WD+4WD ) Lowering T5 Models Front : 100mm ( or 130mm with Hub Modding ) Rear : 130mm ( bump stop modification required ) Fits T6 2015> Multivan, Transporter, California, LKW inc Facelift ( Type 7HC,7HMA,7JO, 2WD+4WD ) Lowering T6 Models Front : 100mm ( or 130mm with hub modding ) Rear : 130mm ( Bump stop modification required ) Fits T6.1 2019> Multivan, Transporter, California, Beach ( Type1HC,7HMA,7LO,2WD+4WD ) Lowering T6.1 Models Front :100mm ( or 130mm with hub modding ) Rear :130mm ( Bump stop modification required ) *Note For vehicles with Electronic dampers use delete kit 93071-1 Contact us if your require fitting. Example coilover image shown, delivered product may vary.£2,080.00 inc VAT£2,080.00 inc VAT -
H&R Deep Coilover Kit for VW Polo 5 6R / 6C1 ( 90mm )
Suspension, H&R Coilover Suspension, Shop by Car, Volkswagen, Polo, H&R CoiloversH&R Deep Coilover Kit for VW POLO 5 (6R1, 6C1) | 03/2009 > Note: Prior to ordering check: Front top shock absorber fixation to the body with one nut, NOT for fixations with three bolts. Lowered front axle from [mm]: 60 • Lowering front axle up to [mm]: 80 Lowered rear axle from [mm]: 60 • Lowered rear axle up to [mm]: 90 This kit is not supplied with top mounts , the original top mounts must be used or replaced if necessary. Fixed damping monotube coilovers offered with Bilstein inserts H&R Linear Springs for ultimate comfort and ride quality. Note: The picture may differ from the delivered product£1,249.99 inc VATThis version offers more lowering range than the normal H&R version. The Product is a version that can achieve lowering beyond the H&R standard lowering adjustment range. Due to vehicle-specific tolerances, additional work & modifications may be necessary on the vehicle. Any of those arising costs incurred in this regard these will not be borne by StillStatic Limited. After installation of coilover suspension, the clearance of drive shafts and the wheel/tyre combination to any kind of safety relevant parts, must be checked in all driving and max. load conditions. If necessary, the vehicle ride height must be adjusted higher. In any case, however, the legally specified minimum ride heights on the vehicle must be observed (direction indicators, light beam angle etc calibrated). StillStatic Limited accepts no liability for any damage that may occur as a result of non-compliance with the above points.£1,249.99 inc VAT -
H&R Deep Coilover Kit for Mazda 3 MPS Typ BL Low version F: 40-70mm / R: 40-60:
Suspension, H&R Coilover Suspension, Shop by Car, Mazda, H&R Coilovers£1,761.99 inc VAT -
H&R Deep Coilover Kit for Audi TT 8N, 4WD / S3 (L) / A3 (L) 50-110mm ( with shorter rear damper )
A3 / S3 / RS3 H&R Deep Coilover Suspension, Audi TT TTS TTRS H&R Deep Suspension£1,663.99 inc VAT -
H&R Race Coilover Kit for Audi A4 + A5 + A6 + A7 B8 Platform incl. Q5 50-120mm Fixed damping:
A4 / S4 / RS4, A5 / S5 / RS5, A6 / S6 / RS6, A7 / S7 / RS7, Q5 / SQ5, RSS Race Coilover SuspensionH&R Race Coilover Kit for Audi A4 + A5 + A6 + A7 B8 Platform incl. Q5 50-120mm fixed damping Fits RS6 C6 4F C7 4G£1,885.00 inc VAT£1,885.00 inc VAT -
H&R Deep Coilover Kit for Audi TT 8N 50-110mm Quattro S3 + A3 Quattro:
TT / TTS/ TTRS£1,450.49 inc VAT -
Muecke Audi TT 8J widened wings 3cm
TT / TTS/ TTRS, Muecke-Carbon & Bodywork Parts ( Wider Wings )- 1 set of fiberglass Audi TT 8 J wing GFK 3 cm wider per side
- unpainted, surface gelcoat gray
- Material report is included, acceptance according to §21 StVZO (individual acceptance)
£449.00 inc VAT -
H&R Deep Coilover Kit for Audi S3 8Y / RS3 Limo 8YA
A3 / S3 / RS3 H&R Deep Coilover SuspensionH&R Deep Coilover Kit for : H&R Deep Coilover Kit for Audi A3 / S3 8Y / RS3 8YA Limo 2019> Lowering 40-80mm EDC cancellation kit 93068-1 These versions offer more lowering than the “normal” monotube version and in some variations include camber adjustable top mounts. H&R are an OE and Motorsport suspension specialist so as expected the ride quality of all Deep version reflects the expert technical knowledge and in house “100% german made ” ethic. This is reflected in the 2 year warranty proving the quality in the product and on the road.If you are unsure which coilover best suits your needs please contact us [email protected]Note: The picture may differ from the delivered productThe Product is a version that can achieve lowering beyond the H&R standard lowering adjustment range. Due to vehicle-specific tolerances, additional work & modifications may be necessary on the vehicle. Any of those arising costs incurred in this regard these will not be borne by StillStatic Limited. After installation of coilover suspension, the clearance of drive shafts and the wheel/tyre combination to any kind of safety relevant parts, must be checked in all driving and max. load conditions. If necessary, the vehicle ride height must be adjusted higher. In any case, however, the legally specified minimum ride heights on the vehicle must be observed (direction indicators, light beam angle etc calibrated). StillStatic Limited accepts no liability for any damage that may occur as a result of non-compliance with the above points.£2,029.00 – £2,939.99 inc VAT -
Audi A1 S1 8X Coilover Suspension Gepfeffert KW V2 Suspension 45-90mm
Shop by Car, Audi, Polo, A1 / S1, KW Gepfeffert Coilover SuspensionAudi S1 8X Quattro ( 170 KW ) 2014> Gepfeffert V2 Coilover£1,790.00 – £2,290.00 inc VATFits the following models:
- Aud S1 8X 2014>
Gepfeffert V2 with / without adjustable camber adjustable top mounts
The gepfeffert V2 with adjustable camber dome bearings is mounted plug and play in the vehicle, without using original installed suspension components with. The chassis with adjustable camber dome bearings have compared to our gepfeffert KW "small depth versions" (without camber dome bearings) an even greater "scope" for even more lowering and even more upgrade options to be able to tune the vehicle even more individually to the requirements of each driver. Example Golf 7 GTI:- Series KW coilover suspension: adjustment range 20-45mm (without camber dome bearing)
- GEPFEFFERT KW "small depth version" (without camber dome bearing): adjustment range 35-70mm
- GEPFEFFERT KW with adjustable camber dome bearings: adjustment range 45-95mm (upgrade possibilities with other spring systems up to 130mm possible)
For more stability or ride comfort. With adjustable rebound damping.
The KW coilover suspension variant 2 "inox-line" is the suspension for the experienced sports driver who wants to make adjustments to the setup in addition to lowering the vehicle individually. The individually adjustable rebound damping ensures better connection on fast road sections and easier vehicle control. In addition, rolling comfort on bad roads can be significantly influenced with adjusted rebound damping.The gepfeffert.com® V2 coilover suspension made by KW
With the KW coilover suspension variant 2 "inox-line", you can influence the handling and comfort yourself as an experienced sports driver through the individually adjustable rebound tuning. The 16 exact clicks allow you to tune the KW dampers tighter or more comfortable without affecting the bottom valve of the compression stage.Technical information:
- damping technology adjustable in the rebound stage in 16 exact clicks - Stainless steel technology inox-line - Individual, stepless lowering - tested adjustment range - ready-to-install complete solution - High quality components for long service life - complete documentation for easy use £1,790.00 – £2,290.00 inc VAT -
H&R Race Coilover Kit for Audi S4 B5 Saloon 50-120mm
Suspension, H&R Coilover Suspension, Shop by Car, Audi, A4 / S4 / RS4, H&R CoiloversH&R Race Derived Coilover Kit for Audi S4 B5 ( 8D ) Saloon Low Version 50-120mm 09/98>
RSS-13-471-5/2SC Fixed damping H&R Deep coilover for Audi S4 B8 lowering 50-120mm. For Avant model please check RSS-13-471-5/1SC For any queries please contact [email protected]£1,959.99 inc VAT -
H&R Deep Coilover Kit for Audi 80 B4 Saloon + Estate S2 Lim. – Avant 4WD 50-100mm
Suspension, H&R Coilover Suspension, Shop by Car, Audi, 80, H&R CoiloversAudi H&R DEEP Coilovers – Audi 80 B4 (8C ) Saloon + Estate 4WD S2 Lim. - Avant 09/91>94 5+6 cylinder This suspension is made with modular race springs.£1,959.99 inc VATThis is a custom made “Deep” version coilover kit made to order. £1,959.99 inc VAT -
MTS Technik Street Coilover Kit Cupra Formentor
MTS Suspension, MTS Technik Coilover FormentorCoilover Kit Cupra Formentor
Coilover Kit MTS Technik for Cupra Formentor, lowering the front axle between 40 - 60 mm, and rear between 40 - 65 mm. Dedicated for the years of: 07/20 -, for the engine version: 2.0TSI 4Drive / 2.5 VZ5 4Drive / 2.0TDI 4Drive. mm. Dedicated for the years of: 07/20 -, for the engine version: 2.0TSI 4Drive / 2.5 VZ5 4Drive / 2.0TDI 4Drive.2 year warranty with no mileage limit to confirm high quality.Suspension components characterized by increased corrosion resistance and made of the highest quality materials.The use of twin-tube technology guarantees stable shock absorber performance.Pressurized gas presses the hydraulic fluid, eliminating the "foaming" effect of the oil (an undesirable and typical for oil shock absorbers phenomenon), which means higher efficiency for continuous, intensive work.Specially selected type of thread and a wide range of suspension adjustment allows optimal setting of the car height.Innovative hexaCOIL spring perch, significantly increasing the comfort of suspension height adjustment.Double zinc plated steel shock absorbers as well as anodized aluminum adjusters and caps to ensure increased corrosion resistance.Coilover springs made by Eibach, the world leader in the sport springs industry.3 - Front and rear axle height adjustable (threaded shock absorber housing on the front, dampers, springs and height adjustable elements on the rear).21 - If the vehicle is equipped with a stock sport suspension, the lowering mentioned in this catalogue will be relatively lower.24 - During the installation of suspension set the clearance between tire/rim and suspension strut shall be checked. The minimum allowed gap is 5mm (0,2 inch). Otherwise use certificated wheel spacers.35 - Rear thread adjustment block is mounted on the top.39 -Installation is also possible for vehicles with electronic damping force adjustment. The electronic system must be deactivated in this case.52 - Only suitable for multilink suspension.£709.00 inc VAT -
MTS Technik Performance Damper for Transporter T5 T6 T6.1
Volkswagen, MTS Suspension Accessories, MTS Suspension, Transporter MTS Coilover SuspensionPerformance Shock Absorber (rear) Volkswagen Transporter T5 T6 T6.1 Volkswagen Transporter T5 / T6 / T6.1 Engine 2.0 / 2.0TSI / 2.0TSI 4motion / 1.9TDI / 2.0TDI / 2.0TDI 4motion / 2.5TDI / 2.5TDI 4motion Year 2003 - 01/15 > 2023 2 years warranty 2 year warranty with no mileage limit to confirm high quality. High quality Suspension components characterized by increased corrosion resistance and made of the highest quality materials. Twin-tube construction The use of twin-tube technology guarantees stable shock absorber performance. Gas technology Pressurized gas presses the hydraulic fluid, eliminating the "foaming" effect of the oil (an undesirable and typical for oil shock absorbers phenomenon), which means higher efficiency for continuous, intensive work. Measurement from centre of bushing : 440mm fully open , 300mm closed.£70.00 inc VAT£70.00 inc VAT -
H&R Deep Coilover kit Cupra Formentor
Cupra Formentor H&R Deep CoiloversH&R Deep coilovers made for StillStatic by H&R Special Suspension Sportwagen SUV Cupra Formentor 2.0 TDI / TSI / 1.5 TSIincl. VZ, type KM 2021> Lowering Front VA : 70-85 / Rear HA : 65-85 This kit is not supplied with top mounts , the original top mounts must be used or replaced if necessary. Fixed damping monotube coilovers offered with and without adaptive damping delete kit, Bilstein inserts H&R Linear Springs for ultimate comfort and ride quality.£1,655.00 – £1,915.00 inc VATNote: The picture may differ from the delivered productThis version offers more lowering range than the normal H&R version. The Product is a version that can achieve lowering beyond the H&R standard lowering adjustment range. Due to vehicle-specific tolerances, additional work & modifications may be necessary on the vehicle. Any of those arising costs incurred in this regard these will not be borne by StillStatic Limited. After installation of coilover suspension, the clearance of drive shafts and the wheel/tyre combination to any kind of safety relevant parts, must be checked in all driving and max. load conditions. If necessary, the vehicle ride height must be adjusted higher. In any case, however, the legally specified minimum ride heights on the vehicle must be observed (direction indicators, light beam angle etc calibrated). StillStatic Limited accepts no liability for any damage that may occur as a result of non-compliance with the above points.£1,655.00 – £1,915.00 inc VAT -
VW Tiguan H&R Deep Coilover 5N Variant AD1 – AX1 2016 > 55-75mm
Tiguan H&R Deep CoiloversH&R Deep coilovers made for StillStatic by H&R Special Suspension for VW Tiguan 5N Variant AD1 - AX1 2016 > 55-75mm Lowering front : 65-75 mm rear : 55-75 mm This kit is not supplied with top mounts uses the original top mounts must be used or replaced if necessary. For vehicles with 55mm diameter strut clamp. please check vehicle axle weight from the vin plate inside drivers side door shut either upto 985 kg or over 985 kg and select suitable option. Fixed damping monotube coilovers, Bilstein inserts H&R Linear Springs for ultimate comfort and ride quality.£1,480.00 inc VATNote: The picture may differ from the delivered productThis version offers more lowering range than the normal H&R version. The Product is a version that can achieve lowering beyond the H&R standard lowering adjustment range. Due to vehicle-specific tolerances, additional work & modifications may be necessary on the vehicle. Any of those arising costs incurred in this regard these will not be borne by StillStatic Limited. After installation of coilover suspension, the clearance of drive shafts and the wheel/tyre combination to any kind of safety relevant parts, must be checked in all driving and max. load conditions. If necessary, the vehicle ride height must be adjusted higher. In any case, however, the legally specified minimum ride heights on the vehicle must be observed (direction indicators, light beam angle etc calibrated). StillStatic Limited accepts no liability for any damage that may occur as a result of non-compliance with the above points.£1,480.00 inc VAT -
MTS Technik Street Coilover Kit Volkswagen Golf 8 Hatchback 2WD + 4WD
MTS Suspension, MTS Technik Mk7 / 7.5 / Mk8Coilover Kit Volkswagen Golf VIII Hatchback
Coilover Kit MTS Technik for Volkswagen Golf VIII Hatchback, lowering both axles between 35 - 70 mm. Dedicated for the years of: 11/12 -, for the engine version: 1.0 TSI / 1.0 eTSI / 1.5 TSI / 1.5 TGI / 1.5 eTSI / 2.0 GTI / 2.0 GTI Clubsport / 2.0 TSI R 4motion / 2.0 TDI / 2.0 TDI 4motion / 2.0 TDI GTD.Series: street Max. Axle Load FA: 1081 - 1180 kgMax. Axle Load RA: -1110 kgLowering FA: 35 - 70 mmLowering RA: 35 - 70 mmCamber / top mount FA: noCamber / top mount RA: noCoilover Main Spring (Front): Spring rate (30 - 55 N/mm)Coilover Main Spring (Rear): Spring rate (80 N/mm)Coilover Helper Spring (Rear): Spring rate (20 N/mm)Info: multilink rear suspensionTUV Certificate: yesDownload information brochure: Download information brochure Download installation manual: Download installation manual Download TUV Certificate: Download TUV Certificate 2 year warranty with no mileage limit to confirm high quality. Suspension components characterized by increased corrosion resistance and made of the highest quality materials. The use of twin-tube technology guarantees stable shock absorber performance. Pressurized gas presses the hydraulic fluid, eliminating the "foaming" effect of the oil (an undesirable and typical for oil shock absorbers phenomenon), which means higher efficiency for continuous, intensive work. Specially selected type of thread and a wide range of suspension adjustment allows optimal setting of the car height. Double zinc plated steel shock absorbers as well as anodized aluminum adjusters and caps to ensure increased corrosion resistance. Coilover springs made by Eibach, the world leader in the sport springs industry.£569.00 – £829.00 inc VAT -
Transporter T5 / 6 / 6.1 356mm Rear Disc Upgrade
Shop by Product Type, Shop by Car, Transporter, Brake KitsRear 356mm x 22mm Big Brake Disc kit Kit Includes New OE Redrilled 356mm Discs New Carriers and adapters New hardware Discs spacer All parts are supplied in raw OE finishes, an example of a completed installed kit is shown with the yellow powder coat finish. We also have Front Transporter brake kit options 365mm with Porsche 6 pot Cayenne caliper, or 400mm SQ7 kit with 6 pot akebono caliper.£550.00 inc VAT£550.00 inc VAT -
H&R Deep Coilover Kit for VW Beetle Type 16 09/11> 55mm With Camber adjustable top mounts ( Front Strut Clamp + Twist Beam Rear ) Lowering : 80-140mm (Copy)
H&R Coilover Suspension, Beetle, H&R CoiloversH&R Deep Coilover to fit Beetle Type 16 with 55mm front hub diameter and twist beam rear suspension only. Lowering is 80-140mm with front adjustable camber top mounts. H&R Deep are monotube dampers with superior comfort while still be lower than " normal " versions. This level of lowering requires correct fitment wheels and potential bodywork, re-setting of headlight level sensors. Supplied suspension may differ from image shown.£2,339.00 inc VAT£2,339.00 inc VAT -
H&R Deep Coilover Kit for VW Beetle Type 16 09/11> 55mm ( Front Strut Clamp + Twist Beam Rear ) Lowering : 60-90mm
H&R Coilover Suspension, Beetle, H&R CoiloversH&R Deep Coilover to fit Beetle Type 16 with 55mm front hum diameter and twist beam rear suspension only. Lowering is 60-90mm. H&R Deep are monotube dampers with superior comfort and are supplied for use with original top mounts.£1,695.00 inc VAT£1,695.00 inc VAT -
MTS Technik Coilover kit BMW 3 Series / E36 Saloon
MTS Suspension, 3 Series MTS Coilover SuspensionCoilover Kit BMW 3 Series / E36 Sedan
Coilover Kit MTS Technik for BMW 3 Series / E36 Sedan, lowering both axles between 40 - 80 mm. Dedicated for the years of: 09/90 - 11/98, for the engine version: 316i / 318i / 318is / 320i / 323i / 325i / 328i / 318tds / 325td / 325tds / M3 3.2.Installation Manuals :Download installation manual MTSGWBM01-C: Download installation manual Download installation manual MTSGWBM01: Download installation manual Download installation manual MTSGWBM116 : Download installation manual Download installation manual MTSGWBM98: Download installation manual Download installation manual MTSGWBM01-S: Download installation manual Download installation manual MTSGWBM116-S: Download installation manual Download installation manual MTSGWBM98-S: Download installation manual £619.00 – £909.00 inc VAT -
MTS Technik Coilover kit BMW 5 Series / E34 Saloon
MTS Suspension, 5 Series MTS Technik CoiloversCoilover Kit BMW 5 Series / E34 Sedan
Coilover Kit MTS Technik for BMW 5 Series / E34 Sedan, lowering the front axle between 20 - 95 mm, and rear between 20 - 85 mm. Dedicated for the years of: 01/88 - 12/95, for the engine version: 518i / 520i / 525i / 530i / 535i / 540i / 524td / 525tds / M5.2 year warranty with no mileage limit to confirm high quality.Suspension components characterized by increased corrosion resistance and made of the highest quality materials.The use of twin-tube technology guarantees stable shock absorber performance.Pressurized gas presses the hydraulic fluid, eliminating the "foaming" effect of the oil (an undesirable and typical for oil shock absorbers phenomenon), which means higher efficiency for continuous, intensive work.Specially selected type of thread and a wide range of suspension adjustment allows optimal setting of the car height.The camber plates allow the wheel angle adjustment and increase the precision of driving.Innovative hexaCOIL spring perch, significantly increasing the comfort of suspension height adjustment.Additional height adjustment at the bottom mounting, allowing the car's height reduction to be changed, without interfering with the spring operation characteristics.Double zinc plated steel shock absorbers as well as anodized aluminum adjusters and caps to ensure increased corrosion resistance.Coilover springs made by Eibach, the world leader in the sport springs industry.2 - Front and rear axle height adjustable (threaded shock absorber housing).8 - Not for 4x4.9 - Only for vehicles without NIVO / OEM pneumatic suspension.21 - If the vehicle is equipped with a stock sport suspension, the lowering mentioned in this catalogue will be relatively lower.24 - During the installation of suspension set the clearance between tire/rim and suspension strut shall be checked. The minimum allowed gap is 5mm (0,2 inch). Otherwise use certificated wheel spacers.26 - Independent height adjustment at the lower brackets on the front dampers.28 - Set includes 2x upper "camber plates" on the front axle.29 - The installation requires the use of OE front struts - they should be cut and welded as described in the attached manual.33 - Including M-Technik.£839.00 inc VAT -
MTS Technik Street Coilover Kit Volkswagen Golf 5 / 6 Jetta 5
MTS Suspension, Golf Mk5 Mk6 MTS Technik CoiloversCoilover Kit Volkswagen Golf V Hatchback
Coilover Kit MTS Technik for Volkswagen Golf V Hatchback, lowering the front axle between 35 - 70 mm, and rear between 35 - 60 mm. Dedicated for the years of: 10/03 - 07/10, for the engine version: 1.4 / 1.4FSI / 1.4TSI / 1.6 / 1.6FSI / 2.0FSI / 2.0GTI / 1.9TDI / 2.0SDI / 2.0TDI.Series: street Housing: goldMax. Axle Load FA: 1036 - 1170 kgMax. Axle Load RA: -1150 kgLowering FA: 35 - 70 mmLowering RA: 35 - 60 mmCamber / top mount FA: optionalCamber / top mount RA: noCoilover Main Spring (Front): Comfort Spring rate (34 - 40 - 70 N/mm)Coilover Main Spring (Rear): Comfort Spring rate (43,6 N/mm)TUV Certificate: yesDownload information brochure: Download information brochure Download installation manual: Download installation manual Download TUV Certificate: Download TUV Certificate Series: sport Housing: goldMax. Axle Load FA: 1036 - 1170 kgMax. Axle Load RA: -1150 kgLowering FA: 35 - 70 mmLowering RA: 35 - 60 mmCamber / top mount FA: yesCamber / top mount RA: noCoilover Main Spring (Front): Spring rate (42,5 - 75 N/mm)Coilover Main Spring (Rear): Spring rate (80 N/mm)Coilover Helper Spring (Rear): Spring rate (20 N/mm)TUV Certificate: noDownload information brochure: Download information brochure Download installation manual: Download installation manual 2 year warranty with no mileage limit to confirm high quality. Suspension components characterized by increased corrosion resistance and made of the highest quality materials. The use of twin-tube technology guarantees stable shock absorber performance. Pressurized gas presses the hydraulic fluid, eliminating the "foaming" effect of the oil (an undesirable and typical for oil shock absorbers phenomenon), which means higher efficiency for continuous, intensive work. Specially selected type of thread and a wide range of suspension adjustment allows optimal setting of the car height. Double zinc plated steel shock absorbers as well as anodized aluminum adjusters and caps to ensure increased corrosion resistance. Coilover springs made by Eibach, the world leader in the sport springs industry.3 - Front and rear axle height adjustable (threaded shock absorber housing on the front, dampers, springs and height adjustable elements on the rear).5 - Stabilizer bars may need to be changed with longer ones if lowering more than 40mm.6 - If the right drive shaft diameter of more than 42 mm, the maximum lowering mentioned in the catalogue is reduced by 15 mm.8 - Not for 4x4.21 - If the vehicle is equipped with a stock sport suspension, the lowering mentioned in this catalogue will be relatively lower.24 - During the installation of suspension set the clearance between tire/rim and suspension strut shall be checked. The minimum allowed gap is 5mm (0,2 inch). Otherwise use certificated wheel spacers.73 - For easier height adjustment, we recommend removing the rear adjustment, changing the position of the spring plate and reinstalling the adjustment on the car.Fits the following models :£529.00 – £1,059.00 inc VAT