Showing all 2 results


Price Filter

2 products

  • £709.00 inc VAT

    MTS Technik Street Coilover Kit Cupra Formentor


    Coilover Kit Cupra Formentor

    Coilover Kit MTS Technik for Cupra Formentor, lowering the front axle between 40 - 60 mm, and rear between 40 - 65 mm. Dedicated for the years of: 07/20 -, for the engine version: 2.0TSI 4Drive / 2.5 VZ5 4Drive / 2.0TDI 4Drive.   mm. Dedicated for the years of: 07/20 -, for the engine version: 2.0TSI 4Drive / 2.5 VZ5 4Drive / 2.0TDI 4Drive.
    2 years warranty 2 year warranty with no mileage limit to confirm high quality.
    High quality Suspension components characterized by increased corrosion resistance and made of the highest quality materials.
    Twin-tube construction The use of twin-tube technology guarantees stable shock absorber performance.
    Gas technology Pressurized gas presses the hydraulic fluid, eliminating the "foaming" effect of the oil (an undesirable and typical for oil shock absorbers phenomenon), which means higher efficiency for continuous, intensive work.
    Specially selected type of thread Specially selected type of thread and a wide range of suspension adjustment allows optimal setting of the car height.
    hexaCOIL adjustable spring perch Innovative hexaCOIL spring perch, significantly increasing the comfort of suspension height adjustment.
    Anti-corrosion protection yellow galvanized Double zinc plated steel shock absorbers as well as anodized aluminum adjusters and caps to ensure increased corrosion resistance.
    Eibach springs Coilover springs made by Eibach, the world leader in the sport springs industry.
    3 - Front and rear axle height adjustable (threaded shock absorber housing on the front, dampers, springs and height adjustable elements on the rear).
    21 - If the vehicle is equipped with a stock sport suspension, the lowering mentioned in this catalogue will be relatively lower.
    24 - During the installation of suspension set the clearance between tire/rim and suspension strut shall be checked. The minimum allowed gap is 5mm (0,2 inch). Otherwise use certificated wheel spacers.
    35 - Rear thread adjustment block is mounted on the top.
    39 -Installation is also possible for vehicles with electronic damping force adjustment. The electronic system must be deactivated in this case.
    52 - Only suitable for multilink suspension.
    £709.00 inc VAT
    £709.00 inc VAT
  • £1,655.00£1,915.00 inc VAT

    H&R Deep Coilover kit Cupra Formentor

    H&R Deep coilovers made for StillStatic by H&R Special Suspension Sportwagen SUV Cupra Formentor 2.0 TDI / TSI / 1.5 TSIincl. VZ, type KM 2021> Lowering Front VA : 70-85 / Rear HA : 65-85 This kit is not supplied with top mounts , the original top mounts must be used or replaced if necessary. Fixed damping monotube coilovers offered with and without adaptive damping delete kit, Bilstein inserts H&R Linear Springs for ultimate comfort and ride quality.    
    Note: The picture may differ from the delivered product
    This version offers more lowering range than the normal H&R version. The Product is a version that can achieve lowering beyond the H&R standard lowering adjustment range. Due to vehicle-specific tolerances, additional work & modifications may be necessary on the vehicle. Any of those arising costs incurred in this regard these will not be borne by StillStatic Limited. After installation of coilover suspension, the clearance of drive shafts and the wheel/tyre combination to any kind of safety relevant parts, must be checked in all driving and max. load conditions. If necessary, the vehicle ride height must be adjusted higher.  In any case, however, the legally specified minimum ride heights on the vehicle must be observed (direction indicators, light beam angle etc calibrated). StillStatic Limited accepts no liability for any damage that may occur as a result of non-compliance with the above points.
    £1,655.00£1,915.00 inc VAT
    £1,655.00£1,915.00 inc VAT