MTS Technik Street Coilover Kit Cupra Formentor
MTS Technik Street Coilover Kit Cupra Formentor
£709.00 inc VAT
Coilover Kit Cupra Formentor
Coilover Kit MTS Technik for Cupra Formentor, lowering the front axle between 40 – 60 mm, and rear between 40 – 65 mm. Dedicated for the years of: 07/20 -, for the engine version: 2.0TSI 4Drive / 2.5 VZ5 4Drive / 2.0TDI 4Drive.
mm. Dedicated for the years of: 07/20 -, for the engine version: 2.0TSI 4Drive / 2.5 VZ5 4Drive / 2.0TDI 4Drive.
2 year warranty with no mileage limit to confirm high quality.
Suspension components characterized by increased corrosion resistance and made of the highest quality materials.
The use of twin-tube technology guarantees stable shock absorber performance.
Pressurized gas presses the hydraulic fluid, eliminating the “foaming” effect of the oil (an undesirable and typical for oil shock absorbers phenomenon), which means higher efficiency for continuous, intensive work.
Specially selected type of thread and a wide range of suspension adjustment allows optimal setting of the car height.
Innovative hexaCOIL spring perch, significantly increasing the comfort of suspension height adjustment.
Double zinc plated steel shock absorbers as well as anodized aluminum adjusters and caps to ensure increased corrosion resistance.
Coilover springs made by Eibach, the world leader in the sport springs industry.3 – Front and rear axle height adjustable (threaded shock absorber housing on the front, dampers, springs and height adjustable elements on the rear).
21 – If the vehicle is equipped with a stock sport suspension, the lowering mentioned in this catalogue will be relatively lower.
24 – During the installation of suspension set the clearance between tire/rim and suspension strut shall be checked. The minimum allowed gap is 5mm (0,2 inch). Otherwise use certificated wheel spacers.
35 – Rear thread adjustment block is mounted on the top.
39 -Installation is also possible for vehicles with electronic damping force adjustment. The electronic system must be deactivated in this case.
52 – Only suitable for multilink suspension.
H&R Deep Coilover kit Cupra Formentor
Cupra Formentor H&R Deep Coilovers
H&R Deep coilovers made for StillStatic by H&R Special Suspension
Sportwagen SUV Cupra Formentor 2.0 TDI / TSI / 1.5 TSIincl. VZ, type KM 2021>
Lowering Front VA : 70-85 / Rear HA : 65-85
This kit is not supplied with top mounts , the original top mounts must be used or replaced if necessary.
Fixed damping monotube coilovers offered with and without adaptive damping delete kit, Bilstein inserts H&R Linear Springs for ultimate comfort and ride quality.
£1,655.00 – £1,915.00 inc VAT
Note: The picture may differ from the delivered product
This version offers more lowering range than the normal H&R version.
The Product is a version that can achieve lowering beyond the H&R standard lowering adjustment range. Due to vehicle-specific tolerances, additional work & modifications may be necessary on the vehicle. Any of those arising costs incurred in this regard these will not be borne by StillStatic Limited.
After installation of coilover suspension, the clearance of drive shafts and the wheel/tyre combination to any kind of safety relevant parts, must be checked in all driving and max. load conditions.
If necessary, the vehicle ride height must be adjusted higher. In any case, however, the legally specified minimum ride heights on the vehicle must be observed (direction indicators, light beam angle etc calibrated).
StillStatic Limited accepts no liability for any damage that may occur as a result of non-compliance with the above points.
£1,655.00 – £1,915.00 inc VAT
MTS Technik Street Coilover for 2K/2KN Caddy Mk3 + Mk4
VW Caddy MTS Coilover kits, MTS Suspension
The Street series suspension is the default configuration of MTS Technik engineers, it guarantees a wide range of lowering and a balance between comfort and stiffness.
Coilover Kit Volkswagen Caddy III
Coilover Kit MTS Technik for Volkswagen Caddy III, lowering both axles between 35 - 90 mm. Dedicated for the years of: 03/04 - 05/15, for the engine version: 1.2TSI / 1.4 / 1.6 / 2.0 / 1.6TDI / 1.9TDI / 2.0SDI / 2.0TDI.
2 years warranty 2 year warranty with no mileage limit to confirm high quality.
High quality Suspension components characterized by increased corrosion resistance and made of the highest quality materials in either Zinc " Gold " or Stainless Steel " Inox ".
Twin-tube construction The use of twin-tube technology guarantees stable shock absorber performance.
Gas technology Pressurized gas presses the hydraulic fluid, eliminating the "foaming" effect of the oil (an undesirable and typical for oil shock absorbers phenomenon), which means higher efficiency for continuous, intensive work.
Specially selected type of thread Specially selected type of thread and a wide range of suspension adjustment allows optimal setting of the car height.
Top mounts with camber adjustment The camber plates allow the wheel angle adjustment and increase the precision of driving.
hexaCOIL adjustable spring perch Innovative hexaCOIL spring perch, significantly increasing the comfort of suspension height adjustment.
Anti-corrosion protection yellow galvanized Double zinc plated steel shock absorbers as well as anodized aluminum adjusters and caps to ensure increased corrosion resistance.
NEW Optional Stainless Steel "INOX" struts.
Eibach springs Coilover springs made by Eibach, the world leader in the sport springs industry.
Make Volkswagen
Model Caddy III
Type 2K/2C
Engine 1.2TSI / 1.4 / 1.6 / 2.0 / 1.6TDI / 1.9TDI / 2.0SDI / 2.0TDI
Year 03/04 - 05/15
Series: street
Check Vehicle Data
Max. Axle Load FA: -1075 kg
Max. Axle Load RA: -1300 kg
Check Vehicle Data
Max. Axle Load FA : - 1075 kg to 1235kg
Max. Axle Load RA: -1300 kg
Lowering FA: 35 - 90 mm
Lowering RA: 35 - 90 mm
Camber / top mount FA: yes
Camber / top mount RA: no
Coilover Main Spring (Front): Spring rate (32 N/mm)
TUV Certificate: no
v3 - Front and rear axle height adjustable (threaded shock absorber housing on the front, dampers, springs and height adjustable elements on the rear).
8 - Not for 4x4.
19 - Only for vehicles equipped with a one-piece leaf spring on the rear axle. If the vehicle is equipped with a two-part leaf spring on the rear axle a one-piece leaf spring has to be purchased seperately (while used in a Caddy - use VW part no. for leaf spring spring 2K0 511 151 N, while used in a Caddy Maxi use VW part no. for leaf spring spring 2K3 511 151 E).
21 - If the vehicle is equipped with a stock sport suspension, the lowering mentioned in this catalogue will be relatively lower.
24 - During the installation of suspension set the clearance between tire/rim and suspension strut shall be checked. The minimum allowed gap is 5mm (0,2 inch). Otherwise use certificated wheel spacers.
44 - Installation of the rear axle adjustment must be carried out in accordance with the instruction.
45 - Front and rear axle height adjustable (threaded shock absorber housing on the front, provided adjustment plates + shock absorbers on the rear axle).
£569.00 – £1,059.00 inc VAT
£569.00 – £1,059.00 inc VAT